- Is 1.5 SWR good?
- What does an SWR reading of 1 1 mean?
- Is higher or lower antenna gain better?
- How do you lower the SWR on a dipole antenna?
- Does coax length affect SWR?
- How do you use a CB linear amplifier?
- What can cause high SWR?
- Does SWR affect reception?
- Why the SWR goes higher when I use an amplifier?
- What is acceptable SWR?
- What does an SWR reading of 4 1 indicate?
- What SWR is too high?
- Does antenna gain affect reception?
Is 1.5 SWR good?
SWR RANGE EXPLANATIONS.
SWR 1.0-1.5: The ideal range.
If your SWR is under 1.5, you’re in great shape.
If you’re at 1.5 and really, really want to drop down to closer to 1 it’s likely possible to do with addition tuning, different equipment or a different mounting location..
What does an SWR reading of 1 1 mean?
What does an SWR reading of 1:1 mean? The best impedance match has been attained. An antenna for another frequency band is probably connected. No power is going to the antenna.
Is higher or lower antenna gain better?
The higher the dBi number of the antenna, the higher the gain, but less of a broad field pattern, meaning that the signal strength will go further but in a narrower direction, as illustrated in the diagram below.
How do you lower the SWR on a dipole antenna?
To raise the frequency of minimum SWR, trim the antenna shorter. Cut each of the dipole’s segments by equal amounts so that the two halves maintain equivalent lengths. If the minimum SWR is minimized at a higher frequency than desired, you must lengthen the wire segments.
Does coax length affect SWR?
“the length of the feedline will not change the swr it will change the apparent reading depending on what wave length you read the swr at. . just as adding a signifigant length of coax, the resultant loss will look like a lower swr.”
How do you use a CB linear amplifier?
How to Hook Up a CB Linear AmpHook up the CB to a car or as a home base. … Place the linear amp in a position close to the unit. … Unhook the CB antenna coaxial cable from the CF, and plug it into the input on the amp. … Hook up the standing wave ratio meter to the linear amp as per the directions on the meter.
What can cause high SWR?
The most common cause of a high SWR is an antenna shorted to ground. There are two places a short can occur in a CB antenna system, in the coax and in the antenna stud.
Does SWR affect reception?
Simplified answer: There is no relationship between SWR and receive performance. … SWR is a measure of the impedance mismatch between your antenna and transceiver. Whether transmitting or receiving, a higher SWR correlates with a less efficient coupling of energy between the transceiver and antenna.
Why the SWR goes higher when I use an amplifier?
“Use only the minimum amount of power necessary to obtain a set meter reading”…….. if the swr meter is connected between the output of the amp and the antenna this rule applies. using more power than necessary to obtain a set meter reading will result in higher swr readings.
What is acceptable SWR?
What is a good SWR reading ? The best reading possible is 1.01:1 (46dB return loss), but usually a reading below 1.5:1 is acceptable. Outside the perfect world a 1.2:1 (20.8dB return loss) is spot on in most cases. To ensure an accurate reading, it is best to connect the meter at the base of the antenna.
What does an SWR reading of 4 1 indicate?
What does an SWR reading of 4:1 indicate? Loss of -4 dB. Good impedance match. Gain of +4 dB. Impedance mismatch.
What SWR is too high?
For instance a SWR too high (over 3:1) all over the band can be an indication of a bad part or junction, poor ground or poor location. An SWR too low over the whole band (1:1 for all 40 channels) can indicate a low efficiency antenna or lossy component. Safe operation of your CB should be with an SWR of 2:1 or less.
Does antenna gain affect reception?
When transmitting, a high-gain antenna allows more of the transmitted power to be sent in the direction of the receiver, increasing the received signal strength. When receiving, a high gain antenna captures more of the signal, again increasing signal strength.